Preparation and Characterization of Poly(2-oxazoline) Micelles for the Solubilization and Delivery of Water Insoluble Drugs

Materials and Reagents

1. PVC tubing (Nalgene, 1/4” ID )

2. Eppendorf tubes (Fisher Scientific, catalog number: 05-408-129 )

3. Pipette tips (Fisher Scientific)

4. 11 mm plastic autosampler vials (Thermo Scientific, catalog number: C4011-13 )

5. UV cuvettes (Fisher Scientific, catalog number: NC0628994 )

6. 0.2-micron syringe filter, Nylon (Fisherbrand, catalog number: 13100108 )

7. Poly(2-oxazoline) triblock copolymer (P[MeOx₃₇-b-BuOx₂₃-b-MeOx₃₇]-piperazine) was synthesized as described previously (Luxenhofer et al., 2010)

8. Drugs were purchased from either Adooq Bioscience, Apex Bio, or LC laboratories and stored at -20 °C

9. Ethanol 200 proof (Fisher Scientific)

10. Normal Saline (Teknova, catalog number: S5815 )

Equipment

1. Pipettes (Fisher Scientific)

2. Sonicator (Branson 2510 ultrasonic bath)

3. Eppendorf heating block (Fisher Scientific, catalog number: 11-715-1250 )

4. Desiccator (LabCorp)

5. Rotor vacuum evaporator (Buchi)

6. Vortex mixer (Fisher Scientific, catalog number: 02215365 )

7. Benchtop microcentrifuge (Thermo Scientific)

8. Eppendorf Centrifuge Minispin (Fisher Scientific, catalog number: 05-090-100 )

9. HPLC (Agilent 1200 series)

10. Zetasizer (Malvern)

Procedure

1. Preparation of drug-loaded POx micelles (Figure 1, Small, μL scale; applicable to single and multi-drug loaded POx micelles)

   1. Prepare stock solutions of the drug and polymer in a common solvent.

      Note: Commonly used solvents for the preparation of POx micelles are ethanol (200 proof), methanol, and acetone. In some cases, a mixture of two solvents is used to dissolve drugs. The concentration of the stock solution is determined by the solubility of the drug/polymer in the solvent. E.g., Prepare Paclitaxel stock solution in ethanol at a concentration of 10 mg/ml and POx stock solution in the same solvent at a concentration of 10 mg/ml (POx is also soluble in acetone and methanol at ≥ 10mg/ml). You will need to use an ultrasonic bath for the dissolution of PTX in ethanol.

   2. Mix the polymer and drug solutions at a predetermined polymer/drug ratio (w/w).

      Note: Polymer:drug weight ratio of 10:2 is a good starting point to determine if the polymer can solubilize the drug. If the thin film disperses well in saline (step 4), work your way up to higher ratios (10:4 and 10:8). E.g., for a 10:4 loading ratio of POx:PTX, add a 50 μl stock solution of POx with a 20 μl stock solution of PTX and mix using a vortex mixer (setting 10; for ~10 s).

   3. Evaporate the solvent by placing the Eppendorf tube containing the drug-polymer mixture in a heating block and blowing a stream of nitrogen gas into the tube.

      The appearance of a clear (not cloudy) thin film is indicative of optimal heating conditions (see Figure 2A). The optimum temperature for evaporation is dictated by the physicochemical properties of the solvent (e.g., vaporization temperature) and drug (e.g., Lipophilicity, polarity, etc.) in use. Of note, the optimized temperature of evaporation for Resiquimod and PTX is 50 °C and 45 °C, respectively, and for other drugs varies from 40 °C to 80 °C.

      Note: A disposable pipette tip can be inserted into the end of a PVC tubing and lowered into the Eppendorf tube to facilitate a gentle flow of nitrogen. Further, residual traces of solvent can be removed by placing the thin film in the desiccator overnight.

      
      

      
      Figure 1. POx micelle preparation workflow (created with BioRender.com)

      
      

   4. Hydrate the thin film with normal saline.

      The volume of saline to be used is determined by the desired final drug(s) concentration. The optimal conditions of hydration vary with each drug. For instance, incubation for 10 min at RT followed by mild agitation by gently flicking the tube is sufficient for solubilizing thin films of Resiquimod. In comparison, Paclitaxel requires incubation at 65 °C for 20 min and gentle agitation every 5 min. The temperature of hydration should be optimized empirically for every single and multi-drug incorporated POx micelles.

      Note: Gentle agitation (using a vortex mixer or gently flicking the tube) is necessary to completely disperse the thin polymer-drug film. Visual inspection is a primary means of telling if the hydration conditions worked. While most drugs solubilize within 10 min, for certain drugs, an additional incubation time can yield better size distribution (Figure 2C) by facilitating specific interactions between the drug and polymer (hydrophobic, hydrogen bonding, etc.)

   5. Centrifuge the micelle solution at 10,000 × g for 2-3 min to separate the unencapsulated drug (pellet) and transfer the supernatant containing the drug-loaded micelles to a new tube.

   6. Depending on the stability of the POx micelle solution of drugs, these can either be stored at 4 °C for up to a couple of weeks or freeze-dried for long-term storage. The lyophilized formulation of POx micelles can be easily re-dispersed in DI water without loss in drug-loading and activity.




2. Preparation of drug-loaded POx micelles (Figure 1, large, mL scale; applicable to single and multi-drug loaded POx micelles)

   1. Follow Steps A1 to A2. Use glass vials to accommodate large volumes of stock solutions and a round-bottom (RB) flask for mixing the drug and polymer solutions.

   2. Evaporate the solvent using a rotary vacuum evaporator. Adjust the temperature of the water bath as needed.

   3. The thin film will form in the bottom half of the RB flask when completed.

   4. Hydrate the thin film with saline and immerse it in the water bath at the optimal hydration temperature for the required time – usually 10 to 15 min.

   5. The micelle solution can be aliquoted into small volumes and centrifuged as in Step A5.

   6. Lyophilize the formulation for long-term storage.




3. Characterization of POx micelles

   The primarily used physicochemical characterization techniques for POx micelles include dynamic light scattering (DLS) for the determination of the size distribution and reverse-phase high-performance liquid chromatography for drug loading.

   1. Sample Preparation for DLS measurement

      1. Dilute the micelles 10-fold in saline.

         Note: Typical dilutions used for DLS measurements of POx micelles range from 1:2-1:50, which correspond to drug concentrations of 0.1 mg/ml to 2 mg/ml.

      2. Use nylon syringe filters of 0.2 microns to separate large particles.

      3. Transfer the filtered solution into a clean cuvette without introducing air bubbles.

      4. Place the cuvette in the sample holder and, following equilibration for at least 2 min, take 3 separate measurements for every sample.

   2. Sample preparation for HPLC measurement

      1. Dilute the micelle sample 50-fold in a mixture of 50/50 acetonitrile (ACN): water (v/v).

      2. Filter the diluted sample using a 0.2-micron syringe filter and transfer 100 μl into an HPLC autosampler vial.

      3. Get rid of any air bubbles from the autosampler vial by gently tapping before placing it in the vial tray.

      4. Prepare the standards by serially diluting the analyte at concentrations ranging from 6.25 μg/ml to 200 μg/ml.

      5. The run settings must be optimized for each drug.

         Note: 60/40 ACN: water, 1 mg/ml flow rate, and 10 μl injection volume is usually a good starting point for most drugs. Spiking the mobile phase solvents with 0.1% trifluoroacetic acid helps sharpen the peaks. Make sure the settings used for the sample are identical to the ones used for standards.

Data analysis

1. DLS Analysis

   The zeta sizer measures fluctuations in the scattered light intensity with time caused by the Brownian motion of nanoparticles to estimate the hydrodynamic size of nanoparticles. DLS analyzes the raw data using two algorithms, viz., cumulant analysis and distribution analysis. The cumulant analysis reports two values: Z-average, which is the mean value of the particle size distribution, and polydispersity index (PDI), which is analogous to variance. A PDI value lower than 0.2 is indicative of monodisperse particles. The cumulant analysis also provides a correlogram (correlation curve), which reports the decay rate of the signal from the sample. The amplitude of the correlogram is representative of signal to noise ratio. The distribution analysis provides Gaussian distributions of the particle size by number, volume, and intensity. Sample concentration, presence of large aggregates, and impurities or marks on the exterior of the DLS cuvettes can all influence the size distribution. More information about data interpretation can be found at https://www.malvernpanalytical.com.

   
   

   
   Figure 2. Representative images of the (A, D) thin film, (B, E) hydrated thin film, and (C, F) DLS volume distribution. The top panel represents drug-incorporated micelles prepared using optimal conditions, as demonstrated by the monodisperse volume distribution with a single peak around 27 nm. The bottom panel is representative of sub-optimal conditions, indicated by the cloudy thin film and the incomplete hydration of the thin film, resulting in polydisperse size distribution with a peak at about 105 nm and a large peak of aggregates in the micrometer range.

   Note: The DLS data were obtained from a separate experiment and do not represent the size distribution of the micelles shown in the images and is used here for demonstration purpose only.




2. Drug Loading

   Chose the wavelength at which the analyte shows maximum absorbance and then integrate the peak in the chromatogram to obtain the area, which corresponds to the concentration of the drug in the sample. The retention time of the sample should compare to that of standards. Once the sample concentration is determined from the standard curve, parameters such as loading efficiency and loading capacity can be obtained from the following equations:
   

   M_drug: The amount of drug incorporated in the micelle

   M_excipient: The amount of polymer used in the formulation

   M_{drug added}: The amount of drug initially fed

Acknowledgments

The original work (Vinod et al., 2020) was funded by the National Cancer Institute (NCI) Alliance for Nanotechnology in Cancer (U54CA198999, Carolina Center of Cancer Nanotechnology Excellence).

Competing interests

A.V.K. is co-inventor on patents pertinent to the subject matter of the present contribution and A.V.K. and M.S.P. have co-founders’ interest in DelAqua Pharmaceuticals Inc. having intent of commercial development of POx based drug formulations. The other authors have no competing interests to report.

References

1. Alves, V. M., Hwang, D., Muratov, E., Sokolsky-Papkov, M., Varlamova, E., Vinod, N., Lim, C., Andrade, C. H., Tropsha, A. and Kabanov, A. (2019). Cheminformatics-driven discovery of polymeric micelle formulations for poorly soluble drugs. Sci Adv 5(6): eaav9784.
2. Di, L., Fish, P. V. and Mano, T. (2012). Bridging solubility between drug discovery and development. Drug Discov Today 17(9-10): 486-495.
3. Gala, U. H., Miller, D. A. and Williams, R. O., 3rd (2020). Harnessing the therapeutic potential of anticancer drugs through amorphous solid dispersions. Biochim Biophys Acta Rev Cancer 1873(1): 188319.
4. Han, Y., He, Z., Schulz, A., Bronich, T. K., Jordan, R., Luxenhofer, R. and Kabanov, A. V. (2012). Synergistic combinations of multiple chemotherapeutic agents in high capacity poly(2-oxazoline) micelles. Mol Pharm 9(8): 2302-2313.
5. He, Z., Wan, X., Schulz, A., Bludau, H., Dobrovolskaia, M. A., Stern, S. T., Montgomery, S. A., Yuan, H., Li, Z., Alakhova, D., Sokolsky, M., Darr, D. B., Perou, C. M., Jordan, R., Luxenhofer, R. and Kabanov, A. V. (2016). A high capacity polymeric micelle of Paclitaxel: Implication of high dose drug therapy to safety and in vivo anti-cancer activity. Biomaterials 101: 296-309.
6. Luxenhofer, R., Schulz, A., Roques, C., Li, S., Bronich, T. K., Batrakova, E. V., Jordan, R. and Kabanov, A. V. (2010). Doubly amphiphilic poly(2-oxazoline)s as high-capacity delivery systems for hydrophobic drugs. Biomaterials 31(18): 4972-4979.
7. Vinod, N., Hwang, D., Azam, S. H., Van Swearingen, A. E. D., Wayne, E., Fussell, S. C., Sokolsky-Papkov, M., Pecot, C. V. and Kabanov, A. V. (2020). High-capacity poly(2-oxazoline) formulation of TLR 7/8 agonist extends survival in a chemo-insensitive, metastatic model of lung adenocarcinoma. Sci Adv 6(25): eaba5542.