Laser Microirradiation and Temporal Analysis of XRCC1 Recruitment to Single-strand DNA Breaks

Materials and Reagents

1. Glass bottom 35 mm Petri dishes (MatTek, catalog number: P35G-1.5-20-C )
   
2. HeLa adherent cells in culture
   
3. Plasmids coding for the fluorescent protein XRCC1-GFP
   Note: The XRCC1 sequence (NCBI P18887) was cloned in the Clontech pEGFP-N1 Vector at the restriction sites EcoRI/ApaI.
   
4. Transfection agents (LipoFectamine 2000) (Life Technologies, catalog number: 11668027 )
   Note: Currently, it is “Thermo Fisher Scientific, Invitrogen™, catalog number: 11668027”.
   
5. DMEM [DMEM(1x) + GlutaMAX™ (Thermo Fisher Scientific, Gibco™, catalog number: 31966-021 )] containing 10% of fetal bovine serum (Thermo Fisher Scientific, Gibco™, catalog number: 16000-044 )

Equipment

1. Cell incubator (Thermo Fisher Scientific, model: NAPCO 5400 )
   Note: Currently, it is “BioSurplus, catalog number: NAPCO 5400 ”.
   
2. Nikon A1 inverted confocal microscope equipped with an environmental chamber allowing the control of temperature, humidity and gas mixture
   Note: The lasers used are the following: 405 nm laser for the micro-irradiation, and a 488 nm Argon-laser to visualize the GFP fluorescence. The objective 63x was used.

Software

1. The NIS Software
   Note: It was used for quantification of the fluorescence intensity at the microirradiation region during time, using the Time Measurement function.
   

Procedure

1. HeLa cells were seeded in 35 mm glass bottom Petri dishes (250,000 cells per dish) and transfected 24 h later with the XRCC1-GFP plasmid using Lipofectamine 2000 according to manufacturer recommendations.
2. 24 h after transfection, microirradiation was carried out with a 405 nm diode laser set to 5% power. The laser power at the exit of the fiber was of 4 mW, and around 1 mW watts at the exit of the 10x Obj.
3. Measurements were performed by immobilizing the laser at 100% in a point bleach with the Digital Handheld Optical Power PM100D from THORLABS.
   
   1. Stimulation and acquisition were performed with the 60x objective at a zoom of 4 using an image size of 512 x 512.
   2. A stimulation line of 5 µm was defined and microirradiation performed for 6 sec. Six images were taken before micro-irradiation, to calculate the basal level of fluorescence. After micro- irradiation, an image was taken every 2 sec during 1 min.
   3. Between 10 and 20 cells are micro-irradiated in each experiment.
   Note: To determine the intensity of the lasers to be used in each different microscope it may be useful to monitor the recruitment of proteins involved in Single Strand Break Repair (SSBR) such as XRCC1 and proteins involved in the repair of Double Strand Breaks (DSBR), such as 53BP1 or NBS1 and keep the conditions that induce recruitment of XRCC1 but not of the DSBR proteins. In our case, only after addition of the DNA intercalant Hoechst 33342 we could observe the recruitment of DSBR proteins so we could validate that in our conditions we were mainly inducing SSB.

Analysis and quantification

1. The fluorescence intensity at the micro-irradiated region is measured for each time point. Six images are taken before the micro-irradiation in order to quantify a mean of fluorescence that will be considered as the basal level of the protein in the region and used to normalize the measurements (this value is set to 1).
2. In order to quantify the enrichment factor of XRCC1 in the micro-irradiation region the intensity observed for each time point is divided by the mean intensity measured before the micro-irradiation.
3. The mean of at least 10 cells is displayed in the graph. Error bars represent the SEM.
4. It is important to check if there is bleaching during the acquisition process and correct for that if necessary. In order to do that we define a Standard Region of Interest (ROI-2) in another cell expressing similar amounts of XRCC1-GFP that is in the same scan area. Fluorescence intensity is monitored both in the micro-irradiated cell and in the non micro-irradiated one during both the stimulation and the acquisition period. If there is bleaching, we will observe a decrease in the fluorescence in the non micro-irradiated cell. It was not the case in our system, so no further corrections were required. If bleaching is observed, it is recommended to adjust the acquisition conditions in order to reduce that problem.

Representative data

Figure 1. HeLa cell expressing the XRCC1-GFP or the mutant protein XRCC1(L360D) were microirradiated with a 405 nm laser. A) Presented images correspond to the cell before microirradiation and 1 min after microirradiation. The microirradiation region is indicated by a dashed line. The mutant protein XRCC1(L360D), that has not any more the ability to be recruited to SSB was used as a control. B) Fluorescence intensity corresponding to XRCC1-GFP at the microirradiated region was quantified and displayed in the graph. Error bars represent the SEM of 10 independent cells.

Acknowledgments

We thank the IRCM microscopy facility. This work was funded by INSERM and grants from the Association pour la Recherche sur le Cancer (PJA 20131200165) and the CEA Radiobiology program.

References

1. Campalans, A., Kortulewski, T., Amouroux, R., Menoni, H., Vermeulen, W. and Radicella, J. P. (2013). Distinct spatiotemporal patterns and PARP dependence of XRCC1 recruitment to single-strand break and base excision repair. Nucleic Acids Res 41(5): 3115-3129.